Bell 36028 Manuel du propriétaire

BELL Phones BY NORTHWESTERN BELL PHONES 36028 Congratulations on your selection of the 36028 from Northwestern Bell Phones. This quality 2.4GHz Dual-h

Base Unit Charger AC Adaptor Plug 9VDC. Adaptor (Figure3) HEADSET CONNECTION One of the special features of your phone is that your handset could util

2. Listen for a dial tone. 3. Dial the telephone number. The phone numbers appear on the LCD Display as you enter the number. 4. When finished with yo

number or a name without the corresponding telephone number in the Phonebook. A. PREFERRED CALLS(VIP) You an assign PREFERRED CALL which will generate

1. Press the SAVE/PHONE BOOK button. 2. Press the UP 01" UN button to find the one you need , press the SHIFT RIGHT -"-button if the name or

7. Press the SAVE/PHONE BOOK button to confirm. IMPORTANT: It is not advisable to save a telephone number without the corresponding name in the Phoneb

OUT OF RANGE WARNING • The handset and base unit communicate up to a certain maximum range. The distance can be affected by weather, power lines, or e

How can I activate my Caller ID? company to confirm that the service is available before you install the device. For you Caller ID unit to function, y

"PRIVATE" will be shown when a call is received from a blocked number. For privacy reasons, some states allow callers the option to prevent

PLACING A CALL FROM THE CALLER LIST i Press the CALLS button. 2. Press the UP OF DN button to select the call record you wish to call back. 3. If the

5. Press the CALLS button to return to STANDBY mode. DELETING ALL RECORDS IN THE CALLER LIST 1. Press the CALLS button. 2. Press and hold RE/PA/DEL bu

IMPORTANT SERVICE INFORMATION Read this manual before attempting to setup or use this instrument. It contains important information regarding safe ins

TIME SET Set the date and time. 5. Press and hold the MENU/SCAN button. Press the TELEPHONE KEYPAD #4 button. Press the EDIT/FLASH button. Use the TEL

5. Press the SAVE/PHONE BOOK button to save the setting. 6. Press the MENU/SCAN button to go back to STANDBY mode. A. PRIVATE RING ON/OFF Turn on or o

TIME/DAY STAMP lCMs and Memo messages are automatically voice-stamped with the current time and day. NOTE: After power failure, the time/day stamp wil

030206A-1 22 You will hear the newly programmed 3-digit security code. NOTE: The factory preset password is " 159". OUTGOING MESSAGE (OGM) T

C. ERASING OGM I. During OGM playback, press ERASE button. MEMORY FULL DETECTION The memory full condition occurs: If 15 minutes of recording time is

The following table lists announcements made after you have pressed 9: Message main menu Repeat message To skip message Delete message To stop functio

MAXIMIZING BATTERY LIFE Repeated use or recharge of Ni-Cd batteries without periodic full discharge results in reduced useable charge time. When you n

TROUBLESHOOTING A. TELEPHONE UNIT TROUBLESHOOTING TABLE SYMPTOM No dial tone Does not ring No power on the handset unit Does not charge Range is limit

B. CALLER ID SYSTEM TROUBLESHOOTING TABLE SYMPTOM The Caller ID panel is blank The Caller ID does not show the caller's name and/or phone number

SAVE THESE INSTRUCTIONS !IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to redu

disconnected at the network interface. 4. Use caution when installing or modifying telephone lines. ! MAINTENANCE 1. Use a damp cloth to clean the pla

91745 for repair/warranty information. The telephone company may ask you to disconnect this equipment from the network until the problem has been corr

36028 CONTROLS DIAGRAM Base Unit (Rear View)

DESCRIPTIONS 030206A-1 6 EDIT/ FLASH Button -(EDIT) Press to edit listed items. (FLASH) Momentarily hangs up the phone to access custom calling featur

CHARGE LED Indicator - Lights up steadily when paging the handset. Lights up steadily when the handset is being charged on the base and turns off when

Handset Battery compart mei Battery Connector (Figure 1) 3. Insert the Ni-Cd battery into the battery compartment. 4. Replace the battery compartment